at_nissan

AUTO TRANS DIAGNOSIS
Nissan_Infinity_a/t - RE4F03A/V

Выключить зажигание, потом снова включить ( положение ACC )
Выключить «overdrive» и перевести селектор в положение «D»
Включить зажигание ( положение “On» )
Транспорант Power на приборной панели загорится на 1-2 секунды и погаснет – система «восприняла» ваши действия и готова к проведению самодиагностики
Перевести селектор в положение «2»
Включить Overdrive
Перевести селектор в положение «1»
Выключить Overdrive
Нажать и отпустить педаль газа
Лампочка Power начнет мигать, «выдавая» коды неисправностей ( если они есть):


0505........... No Codes In System
1208 .................... Fluid Temp Sensor/ATCU
Power Source Circuit
1102...................... Vehicle Speed Sensor
1207 ............... Engine Speed Signal Circuit
1103 ........................ A/T 1st Signal
1104 ........................ A/T 2nd Signal
1105 ........................ A/T 3rd Signal
1106 ................. A/T 4th Signal Or TCC
1204........... Torque Converter Solenoid Valve
1205 ............. Line Pressure Solenoid Valve
1108 .................. Shift Solenoid Valve "A"
1201 .................. Shift Solenoid Valve "B"
1206 ........ Throttle Position Sensor Or Switch
1203 ............. Overrun Clutch Solenoid Valve

AUTO TRANS DIAGNOSIS - RE4F04A/V
Nissan


OBD-II/MIL DTC Description
P0000/0505 ...................................... No Codes In System.
P0705/1101 ........................................ Inhibitor Switch
P0710/1208 ............. Transmission Fluid Temperature (TFT) Sensor
P0720/1102 ............ A/T Revolution Sensor (Vehicle Speed Sensor)
P0725/1207 ................................. Engine Speed Signal Ckt
P0731/1103 (1) ...................................... A/T 1st Signal
P0732/1104 (1) ...................................... A/T 2nd Signal
P0733/1105 (1) ...................................... A/T 3rd Signal
P0734/1106 (1) ............................... A/T 4th Signal Or TCC
P0740/1204 ...................................... TCC Solenoid Valve
P0744/1107 ...................................... TCC Solenoid Valve
P0745/1205 ............................ Line Pressure Solenoid Valve
P0750/1108 ................................ Shift Solenoid Valve "A"
P0755/1201 ................................ Shift Solenoid Valve "B"
P1705/1206 ...................... Throttle Position Sensor Or Switch
P1760/1203 ........................... Overrun Clutch Solenoid Valve
(1) - Malfunction cannot be displayed by MIL if another malfunction is
assigned to OD OFF/POWER light.
NOTE: Flash codes are also referred to by the manufacturer as
Judgement Flickers.
TCM Self-Diagnostic Procedure
1) Ensure engine is at normal operating temperature. Turn
ignition switch to OFF position and wait 5 seconds. Turn ignition
switch to ACC position. Move shift selector lever to "P" position.
Turn ignition switch to ON position. O/D indicator light should
illuminate for about 2 seconds. If light does not illuminate, go to
O/D OFF INDICATOR LIGHT under ELECTRONIC COMPONENT & CIRCUIT TESTS.
Repair as needed. Go to next step.
2) Turn ignition off, then to ON position. Move shift
selector lever to "D" position. Turn ignition switch to OFF position.
Set O/D switch button to OFF position. Turn ignition switch to ON
position.
3) After 2 seconds, move shift selector lever to "2"
position. Set O/D switch button in ON position. Move shift selector
lever to "1" position. Set O/D switch button to OFF position.
4) Depress accelerator pedal to floor and release pedal.
Record O/D OFF indicator light flashes. Where the LONG light flash
appears in the flash sequence (1st, 2nd, 3rd etc.) indicates the code.